CYBEX 700T Manual de Serviço Página 1

1- SafetyIMPORTANT: Read all instructions and warnings before using the treadmill.Important Voltage InformationBefore plugging the power cord into an

grounded, dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230VAC, 60 Hz, and 15 amps, or 220/240 VAC, 50 Hz and 15 amps. M

• Do not operate the treadmill if the cord is damaged, if the treadmill is notworking properly, or if the treadmill has been dropped or damaged. Seeks

Caution LabelsCaution labels indicate a potentially hazardous situation, which, if not avoided, may result inminor or moderate injury. The caution lab

Emergency StopPress the STOP key once to bring the running belt to a stop.Cybex 700T Treadmill Owner’s ManualPage 1-5Front PagesAbout this Manual . .

Cybex 700T Treadmill Owner’s ManualPage 1-6

2 - Technical SpecificationsSpecificationsLength: 82" (208 cm)Width: 33" (84 cm)Overall Height: 59" (150 cm)Running Area: 20" x 60

Cybex 700T Treadmill Owner’s ManualPage 2-2

3 - OperationRead and understand all instructions and warnings prior to using equipment.See all of the safety related information located in chapter 1

dedicated circuit, and one of the following: 115 VAC, 60 Hz and 20 amps, or 230 VAC, 50Hz, and 15 amps, or 208/220 VAC, 60 Hz and 15 amps.2. Locate th

Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. Stableflex and the Stableflex logo are registered trademarks of Cybex

Use the - + keys to adjust the weight number displayed in the right windowto reach your current weight. The 700T accepts weights from 50 to 400 lbs.(2

Press the STOP key a second time to begin a workout review. The totals reached during yourworkout session will cycle and the five minute pause will en

programs P2-P6. NOTE: You cannot, however, switch from a programmedworkout to any other program without ending your current workout and losingyour acc

With respect to treadmills, the percent grade is roughly equal to the increase in height (rise) ofthe treadmill divided by the length (run) of the tre

NOTE: Please note that Cybex does not recommend continuous holdingof the handrails or the contact heart rate grips while running. Use of ProgramsThe 7

warm-up and cool-down period. You can warm-up by setting a slow speed forwalking/jogging on the treadmill at zero incline and then gradually increase

Cybex 700T Treadmill Owner’s ManualPage 3-9Front PagesAbout this Manual . . . . . . . . . . iFCC Compliance Information . iDeclaration of Conformity

P3 — Cardiovascular ProgramThe P3 Cardiovascular Program is a thirty-minute workout that uses high-intensity, aerobicexercise to strengthen the heart

Cybex 700T Treadmill Owner’s ManualPage 3-11Front PagesAbout this Manual . . . . . . . . . . iFCC Compliance Information . iDeclaration of Conformit

P4 — Weight Loss ProgramThe P4 Weight Loss Program is a forty-five-minute walking workout designed to help you loseweight. In this program, weight los

Cybex 700T Treadmill Owner’s ManualPage 3-13Front PagesAbout this Manual . . . . . . . . . . iFCC Compliance Information . iDeclaration of Conformit

P5 — Fitness Test ProgramThe P5 Fitness Test Program is a twenty-minute walking workout designed to test youraerobic walking capacity. It is the guide

The 700T is designed to help you set goals and measure your progress. Thekey is to evaluate your fitness level “L” and to re-evaluate it periodically

P6 — Saved ProgramIn addition to the four programmed workouts included with the 700T, you can also create yourown workout by manually changing the spe

Workout TipsMonitoring Your Heart RateExercise doesn't have to be painful to be effective. On the contrary, researchhas shown that simply by rais

Cybex 700T Treadmill Owner’s ManualPage 3-18Visit our website at www.ecybex.com/education to use the body mass calculator, caloriecalculator, and to g

4 - Preventive MaintenanceRegular Maintenance ActivitiesPreventive maintenance activities must be performed to maintain normaloperation of your treadm

To clean the motor components, you must remove the two Phillips head screws that hold themotor cover in place. Lift the cover, and put it and the scre

Re-tensioning and Re-centering the Belt — Follow the procedure below.Tools Required• 3/4" wrench 1. Re-tension the belt.A. Use a 3/4" wrench

same bolt. Once the running belt has been adjusted closer to the center of thetreadmill use about 1/4 of a turn until the belt has been stabilized.B.

IMPORTANT WARRANTY INFORMATIONTo validate this warranty, complete the following information and return this card to Cybex within ten days of equipment

B. Run your hand under the belt on the top of the deck surface. If you feelexcessive ridges or cracks, or if the deck feels grooved yet highlypolished

Other Preventive MaintenanceCybex recommends that the following maintenance activities be completed by a qualifiedservice technician. These activities

Service ScheduleAll of the activities listed below should be performed at the time of reaching themileage listed. As a aid to keep this schedule, Serv

Log SheetCybex 700T Treadmill Owner’s ManualPage 4-8Serial Number Date of Installation Total Miles/KilometersTotal HoursMotor Current @3 mph (4.8

5 - Setup & AssemblyQuick SetupQuick Setup - For Experienced Fitness Professionals Only1. The power requirements for this treadmill are a grounded

Cybex 700T Treadmill Owner’s ManualPage 5-2Figure 1Item Qty Description1 1 Base 2 1 Left upright3 1 Right upright4 1 Console assembly5 1 Upright cross

vapor, chlorine, and/or bromine could adversely affect the electronics as well asother parts of the machine.A comfortable environment will help you en

Assembling the TreadmillTo ensure correct assembly of the treadmill, carefully follow these steps:NOTES: • In this manual the words “left” and “right”

4. Attach the console to the left upright.A. Place the console assembly on the floor with the display side facingdown and place the left upright on th

! CAUTION: Be sure that the display cable does not get pinched, cut or damagedduring this process.5. Attach the console and left upright to the treadm

ATTN: CUSTOMER SERVICECYBEX INTERNATIONAL10 TROTTER DRIVEMEDWAY, MA 02053-9934NO POSTAGENECESSARYIF MAILEDIN THEUNITED STATESBUSINESS REPLY MAILFIRST

7. Connect the cables.A. Note that there are four threaded holes on the treadmill's front frameused to fasten the front end panel to the treadmil

C. Place the front end panel inposition on the front of thetreadmill. See Figure 8.D. Using the Allen wrench, attachthe front end panel with fourbutto

Test the 700T OperationUse the following instructions to test the full speed and incline range of thetreadmill and to check the belt for proper operat

9. Observe the belt to see that it is running properly; it should stay centered in the middleof the deck. If you have problems with the running belt o

Setting Operation OptionsThe 700T's Setup Mode allows you to configure the following features:1. Memory Retention Mode2. Metric/English Measureme

Memory Retention On: When this feature is enabled (“on”), the 700T uses your last programvalues as the new default program, level, and weight, replaci

selected, the pause function is turned off and not available for use. To togglebetween “on” and “oFF,” use the v^keys.6. Service RemindersService Remi

Cybex 700T Treadmill Owner’s ManualPage 5-14

6 - Customer ServiceContacting ServiceHours of phone service are Monday through Thursday from 8:30 a.m. to 6:00p.m. and Friday from 8:30 a.m. to 5:00

warranty shall be strictly and exclusively limited to repairing or replacing free of charge, F.O.B.origin, those parts and materials which are, in Sel

Page iCybex 700T Treadmill Owner’s ManualAbout This ManualFor your convenience, all measurements and voltage requirements are listed in both Englishan

said manufacturer to Seller. In this regard, Seller agrees to certify to Buyer theidentity of the supplier of items claimed to be defective so the Buy

PROCEDURE FOR OBTAINING WARRANTY PERFORMANCE:TO SECURE THIS WARRANTY IN EVENT OF A DEFECT, BUYER MUST RETURN TO SELLERTHE WARRANTY REGISTRATION CARD.

NOTE: Merchandise returned without an RMA number on the outside ofthe package or shipments sent C.O.D. will not be accepted by theCybex receiving depa

Cybex 700T Treadmill Owner’s ManualPage 6-6

7 - ServiceService Instruction! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do so could result in serio

! WARNING: Keep wet items away from inside parts of the treadmill. Electrical shockcould occur even if the treadmill is unplugged.1. Turn the power on

be pitted or blackened on one edge. Too many of these indicate a worncommutator, and the motor should be replaced. The commutator maybe cleaned with n

10. Secure the front panel.A. Avoid touching R34 and the black capacitors. Connect the motor cable. See Figure 1.B. Using a 3/16” Allen wrench, secure

displayed should not exceed 10.9 for a 115V unit, and 9.1 for a 220V unit. Witha user of any weight, the current should not exceed 17.9 for a 115V uni

3. Remove the motor cover and side rails.A. Remove the two Phillips head screws that fasten the motor cover to the frame. Lift thecover and set it asi

Cybex 700T Treadmill Owner’s ManualPage iiDeclaration of Conformity We declare that to the best of our knowledge that the fitness equipment listed bel

10 mph (16 kph) with no load should not go below 168 VDC. If it is below83/168 VDC respectively, the magnets are weak and the drive motorshould be rep

A. Using a 3/16” Allen wrench, remove the two button head screws that fasten each siderail to the frame. This step will also loosen the end caps.B. Gr

7. Remove the front roller.A. Using a 1/2” wrench, remove the two screws and four washers thatfasten the front roller to the front end assembly. B. Li

12. Attach the drive belt tensioning assembly.A. Place the drive belt tensioning roller in position under the front bracket on the drivebelt tensionin

Running Belt Adjustments in the Preventive Maintenance chapter.Then continue with step 17.17. Attach the motor cover.A. Lower the motor cover and in p

suspect the lower board and then the display board. This signal can also be seen on adiagnostic LED of the display board.If the drive motor (and runni

voltage. The cause of this error can usually be attributed to noise or“interference” from the power line. An electrical device with a high speedmotor,

Cybex service representative or directly to Cybex Technical Support. An authorized Cybextechnician can usually detect the source of the problem with a

To exit the diagnostic test mode, press the STOP key at any time. This willreturn you to the mode you were in before entering Diagnostic Tests.d1: Sof

Active keys during this test (hold keys for two seconds):START/ENTER will advance you to the next diagnostic test.STOP will exit and return you to the

Cybex 700T Treadmill Owner’s ManualPage iiiFront PagesAbout this Manual . . . . . . . . . . . . . . . . . . iFCC Compliance Information . . . . . . .

For example, for the + key:d6 64Active keys during this test (hold keys for two seconds):START/ENTER will advance you to the next diagnostic test.STOP

Cybex 700T Treadmill Owner’s ManualPage 7-18SHIFT backs you up one step in the diagnostics test menu.d9: Number of StartsThis test displays the total

Cybex 700T Treadmill Owner’s ManualPage 7-19Front PagesAbout this Manual . . . . . . . . . . i3 OperationQuick Operation Guide . . . . 3-1Detailed O

Cybex 700T Treadmill Owner’s ManualPage 7-20To turn off a Service Reminder, press the + key, and the right window will display the ServiceReminder cle

Cybex 700T Treadmill Owner’s ManualFront PagesAbout this Manual . . . . . . . . . . i3 OperationQuick Operation Guide . . . . 3-1Detailed Operation

Cybex 700T Treadmill Owner’s ManualITEM QTY. PART NO. DESCRIPTIONNO.36 1 HS-14969 Screw, (For Flex Deck)37 1 BD-14072 Belt, Drive, Poly - V, 280J10

Cybex 700T Treadmill Owner’s ManualPage 7-23Front PagesAbout this Manual . . . . . . . . . . i3 OperationQuick Operation Guide . . . . 3-1Detailed O

Cybex 700T Treadmill Owner’s ManualPage 7-24

Cybex 700T Treadmill Owner’s Manual Page 7-25

LINEELEV2 12 112323133121212 1 212 1 2335654121014DISPLAY CONN.181620POT WIPEVREF+5V VCC+5V VCCE-STOP6V RTNE-STOP+6V AUXE-STOP+5V VCCCIRCUIT GND151311

Cybex 700T Treadmill Owner’s Manual