CYBEX TROTTER Manual de Serviço

Cybex and the Cybex logo are registered trademarks of Cybex International, Inc. TROTTER and the TROTTER logo are registeredtrademarks of Cybex Intern

Important Safety Instructions(Save These Instructions)! DANGER: To reduce the risk of electric shock, always unplug this treadmill from theelectrical

Cybex TROTTER Elite Treadmill Owner’s & Service ManualDisplay CableTools Required• Phillips head screwdriver• ESD (Electro Static Discharge) groun

Cybex TROTTER Elite Treadmill Owner’s & Service ManualB. Disconnect the display cable (P1 and P2) from the lower board. See Figure 21.C. Disconnec

8. Secure the left junction covers.A. Using a Phillips screwdriver, tighten the three screws that hold the junction covers in place.9. Secure the moto

10. Secure the console back.A. While being sure not to pinch any cables, attach the top console back to the consolefront with the five Phillips head s

5. Attach the console back.A. While being sure not to pinch any cables, secure the console back to the console withthe five Phillips head screws.6. Te

Cybex TROTTER Elite Treadmill Owner’s & Service ManualITEM PART NO. DESCRIPTIONNO.41 AF-16382 Elevation, weldment42 HS-60022 Bolt Hhcs 0.375 x 2

Cybex TROTTER Elite Treadmill Owner’s & Service ManualITEM PART NO. DESCRIPTIONNO.100 AX-16728 Lower Rear Console Assembly100 PL-16409 Console,

Cybex TROTTER Elite Treadmill Owner’s & Service Manual Page 7-41

AW-17163 (INTL)AW-17164 (INTL)CAPACITOR10uF, 370VACCA-168135mH CHOKETR-16814 (x2)POWER FACTORAX-16812ASSYCORRECTIONAW-17112(BLK)AW-17113(WHT)BLACKREDY

• Use a dedicated line when operating the treadmill.• Connect the treadmill to a properly grounded outlet only.• DO NOT operate electrically powered t

• Ensure all User and Facility safety precautions are observed.• Carefully read and understand the following before using the Pro+ treadmill:• Warning

Cybex TROTTER Elite Treadmill Owner’s & Service ManualUnderneathMotor CoverSafetyPage 1-5

Cybex TROTTER Elite Treadmill Owner’s & Service Manual VARNINGKOPPLA IFRÅN STRÖMMEN INNAN SERVICE UTFÖRS.SafetyPage 1-6

Caution DecalsCaution decals indicate a potentially hazardous situation, which, if not avoided, may result inminor or moderate injury. There are no ca

Cybex TROTTER Elite Treadmill Owner’s & Service Manuale-stop+-4. The treadmill is now ready to be used.5. After use, remove the e-stop key from th

2 - Technical SpecificationsSpecificationsLength: 79” (200 cm)Width: 32” (82 cm)Running Area: 20” x 58” (51 cm x 147 cm)Weight of Product: 385 lbs. (1

Cybex TROTTER Elite Treadmill Owner’s & Service ManualSpecifications Page 2-2This page intentionally left blank

3 - OperationRead and understand all instructions and warnings prior to using the treadmill. See all of thesafety related information located in chapt

Quick Operation GuideNOTE: Maximum user weight is 400 lbs. (181 kg).The following is a quick overview of the operation of the treadmill. For more info

3. Place your feet on the two top steps located on each side of the running belt.4. Clip the e-stop clip onto your clothing and carefully test the e-s

9. Press the Speed + — keys to change the belt speed at any time. The right display willshow the set speed. 10. Press the Incline keys to change the i

Stopping the TreadmillPress Stop once to pause your workout for 20 seconds (default setting) and to enter theWorkout Review. The belt will stop and th

Control During OperationControl keys on the display are usable during operation and may be pressed at any time tomake adjustments in speed, elevation,

To review accumulated data after a program: The display automatically cycles throughyour accumulated workout data during the Workout Reviewfor 20 seco

NOTE: When wearing a Polar compatible transmitter, the contact heart rate will dominateonly when the grips are held.Polar Compatible Reception — To us

Use of Programs! WARNING: Obtain a medical exam before beginning any exercise program. Begincomfortably with a lower level and progress with higher le

Manual ModeManual Mode is not a preprogrammed workout. Instead, it allows you to choose settings asyou workout. You may choose your settings according

Calorie GoalProgram OverviewThe Calorie Goal program uses a mixture of increased elevation or speed intervals to provideadded work to this walking and

IMPORTANT WARRANTY INFORMATIONTo validate this warranty, complete the following information and return this card to Cybex within ten days of equipment

5K RunProgram OverviewThis program is designed to help the user train for a 5K race in a systematic fashion. It uses apredefined speed for each level

Cybex TROTTER Elite Treadmill Owner’s & Service ManualSpeedElevation %Warm Upin MinutesProgram Segments in 400 Meters (0.248 Miles) Profiles Show

9 HolesProgram OverviewIn this program, the user chooses their speed as they go. The level of the program usesvariations in the elevation. As the leve

Cybex TROTTER Elite Treadmill Owner’s & Service ManualProfiles Show Level 109 HolesSpeedElevation %Program Segments in YardsRepeatingSegment151413

Heart RateProgram OverviewThe Heart Rate Control program is interactive. By selecting a predetermined heart rate, thetreadmill will adapt the elevatio

Cybex TROTTER Elite Treadmill Owner’s & Service ManualWarmUpProgram Segments in MinutesProgram Segments in MinutesSpeedElevation %CoolDownWarmUpCo

Cybex TROTTER Elite Treadmill Owner’s & Service ManualCustom Program 1NOTE: If this program doesn’t run as indicated in this description and profi

Cybex TROTTER Elite Treadmill Owner’s & Service ManualWarmUpProgram Segments in MinutesProgram Segments in MinutesSpeedElevation %CoolDownWarmUpCo

Custom Program 2The Weight Loss program will be on your treadmill at the time you receive it. See Figure 10.NOTE: If this program doesn’t run as indic

Cybex TROTTER Elite Treadmill Owner’s & Service ManualSpeedProfiles Show Level 10 at 20 MinutesElevation %Weight Loss Custom 215141312111098765432

ATTN: CUSTOMER SERVICECYBEX INTERNATIONAL10 TROTTER DRIVEMEDWAY, MA 02053-9934NO POSTAGENECESSARYIF MAILEDIN THEUNITED STATESBUSINESS REPLY MAILFIRST

Create a Custom ProgramIn addition to the four programmed workouts included with the TROTTER Elite, you can alsocreate your own workouts. You can even

4 - Preventive MaintenanceWarnings/CautionsAll warnings and cautions listed in this chapter are as follows:! WARNING: All maintenance activities shall

NOTE: Do not spray cleaning solution directly on the treadmill. Direct spraying could causedamage to the electronics and may void the warranty. ! WARN

often to prevent premature wear of the deck, running belt, and the drive motor system. Seethe Service Schedule in this chapter to determine the minimu

NOTE: While centering the belt choose one bolt to adjust. Do not adjust both bolts.A. With the treadmill running at 5 mph (8 kph) observe the running

A. Using a Phillips head screwdriver, remove the screw that holds each end cap in place. See Figure 3.4. Remove the side panels.A. Pull each side pane

8. Secure the top steps.A. Place each top step in position. See Figure 4.B. Using a Phillips head screwdriver, tighten the three screws that hold each

Service ScheduleCybex TROTTER Elite Treadmill Owner’s & Service ManualPreventive MaintenancePage 4-7

Log SheetCybex TROTTER Elite Treadmill Owner’s & Service ManualSerial Number Date of Installation Total Miles/KilometersTotal HoursMotor Curr

5 - Setup & AssemblyWarnings/CautionsAll warnings and cautions listed in this chapter are as follows:! WARNING: Use extreme caution when assemblin

Cybex TROTTER Elite Treadmill Owner’s & Service ManualPage iAbout This ManualAn Owner’s & Service Manual is shipped with each Cybex TROTTER El

Electrical Power RequirementsThe power requirements for this treadmill are a grounded, dedicated circuit, rated for one ofthe following: 115 VAC ±5%,

Item Qty Part Number Description1 1 Varies Base with uprights and console attached5 1 AX-16724 Motor cover, center, with decals6 1 PL-16465 Motor c

D. Check off ( ✔) each item in the hardware pack as you find it. See Figure 3. Cybex TROTTER Elite Treadmill Owner’s & Service Manual4714325226242

! CAUTION: A minimum of two people are required to lift, move and assemble thistreadmill. Always use proper lifting methods when moving heavy items.4.

A. Verify that you have the correct model by looking at the console and reading themodel name.B. Verify that you have the correct voltage by looking a

B. Using the hex key provided, tighten the two pivot screws on the handrail. See Figure9. 9. Remove the left side panel.A. Pull the left side panel aw

Front routing:a. Unwind the power cord and route it under the upright. b. Slide the grommet into the front exit hole with the curved end first. See Fi

11. Attach the motor cover (three pieces). A. Using a Phillips head screwdriver, partially tighten each motor cover side (left and right)with four 10-

15. Connect to your computer (optional).NOTE: Skip step 15A-15C if you are notusing your CPA.A. Connect the CPA cable that comeswith your treadmill in

! WARNING: Be sure that all electrical requirements are met as indicated in thespecifications at the front of the manual and at the beginning of thisc

Cybex TROTTER Elite Treadmill Owner’s & Service ManualPage iiNOTE: For European customers only.

11. Run the treadmill through its full % grade range. Press the Incline key until thetreadmill reaches its highest grade (15%). Next press the Incline

Safety Sentry — This is how long the running belt will keep moving if the user steps offthe treadmill. Choices are between none seconds and 1 minute.

Cybex TROTTER Elite Treadmill Owner’s & Service ManualThis page intentionally left blankSetup & Assembly Page 5-14

6 - Customer ServiceContacting ServiceHours of phone service are Monday - Friday from 8:00 a.m. - 6:00 p.m. Eastern Time.For Cybex customers living in

1. Call the Customer Service Hotline listed above for the return of any item that isdefective.2. Provide the technician with a detailed description of

Damaged PartsMaterials damaged in shipment should not be returned for credit. Shipping damages are theresponsibility of the carrier (UPS, Federal Expr

Cybex TROTTER Elite Treadmill Owner’s & Service ManualThis page intentionally left blankCustomerServicePage 6-4

Cybex TROTTER Elite Treadmill Owner’s & Service Manual7 - ServiceWarnings/CautionsAll warnings and cautions listed in this chapter are as follows:

Cybex TROTTER Elite Treadmill Owner’s & Service Manual! WARNING: All maintenance activities shall be performed by qualified personnel.Failure to d

LED FunctionsLEDs are used to indicate the status of many of the treadmill inputs. After entering Test Moderefer to the following list to check that t

Cybex TROTTER Elite Treadmill Owner’s & Service ManualPage iiiFront PagesAbout this Manual . . . . . . . . . . . . . . . . . . iFCC Compliance In

Error CodesError codes notify you of a problem condition and are displayed on the center of the console.These codes can also help to indicate the part

motor cover of each Cybex Trotter Elite treadmill. By performing these procedures you canevaluate the performance of your drive motor and help prevent

5. Check the motor voltage.A. Plug the treadmill back in and turn it to the on (I) position.B. Without standing on the belt, press the Quick Start key

4. Adjust the speed sensor gap (if needed).A. Using a Phillips head screwdriver, loosen the screw that attaches the speed sensor tothe motor saddle. S

IR CompensationNOTE: This procedure is required after replacing the lower control board or the drive motor.Tools Required• Phillips head screwdriver•

F. Using a plastic small flat head screwdriver, turn the IR control slightly in one directionas follows: • Turn clockwise to remove the slack from the

Cybex TROTTER Elite Treadmill Owner’s & Service ManualRunning Belt & DeckNOTE: During this procedure you will have the option to remove the ru

Cybex TROTTER Elite Treadmill Owner’s & Service Manual4. Remove the side panels.A. Pull each side panel out and off the treadmill. See Figure 5.5.

7. Loosen the deck.A. Using a 7/16” open-end or socket wrench, remove the ten screws and ten washersthat hold the deck in place. See Figure 7. NOTE: L

B. Lift one side of the deck and slide it out of the running belt. C. Tilt up the left side of the front roller and slip the running belt off. 10. Ins

This page intentionally left blank

Cybex TROTTER Elite Treadmill Owner’s & Service ManualD. Confirm that the drive belt is positioned three grooves overfrom the face of the flywheel

20. Secure the motor cover.A. Lower the motor cover center into position. See Figure 2.B. Using a Phillips head screwdriver, tighten the three screws

4. Remove the motor straps and drive belt from the motor.A. Using 7/16” open end wrench, remove the nut on each motor strap and remove themotor straps

D. If you are replacing the drive belt, slip the drive belt off the front roller pulley anddiscard it.7. Attach the front roller.A. Slide the new driv

Cybex TROTTER Elite Treadmill Owner’s & Service Manual! CAUTION: If the drive motor is warm wait until it is cool to the touch beforeproceeding. T

Cybex TROTTER Elite Treadmill Owner’s & Service Manualwear such as arcing, pitting, burning, or uneven wear. Commutator bars that are 'dirtyp

C. Using a straight-edge (such as the lowerboard shield), line up the face of theflywheel pulley with the face of the frontroller pulley until they ar

E. Refer to the lower board shieldto confirm the locations for the connectors and check tosee that all of the cables areconnected firmly. See Figure 1

Cybex TROTTER Elite Treadmill Owner’s & Service ManualElevation MotorTools Required• Phillips head screwdriver• Wooden block 4” (10 cm) tall (2)•

Cybex TROTTER Elite Treadmill Owner’s & Service Manual6. Calibrate the elevation motor.A. The switch should be at zero elevationbefore adjusting t

1- SafetyIMPORTANT: Read all instructions and warnings before using the treadmill.Important Voltage InformationBefore plugging the power cord into an

Cybex TROTTER Elite Treadmill Owner’s & Service ManualLower Control BoardNOTE: You will remove and replace the entire lower bracket in this proced

Cybex TROTTER Elite Treadmill Owner’s & Service ManualB. Remove the entire bracket with its lower board. NOTE: Cybex may want this part back for e

8. Secure the line filter.A. Using a Phillips head screwdriver, secure the two screws that hold the line filter to thelower control board bracket. 9.

Cybex TROTTER Elite Treadmill Owner’s & Service Manual2. Remove the motor cover.A. Using a Phillips head screwdriver, loosen three screws on each

Cybex TROTTER Elite Treadmill Owner’s & Service ManualLine FilterNOTE: If you are replacing the line filter follow steps 7 and 8. If not skip to s

Cybex TROTTER Elite Treadmill Owner’s & Service ManualD. With the ground wire through the access hole to the lower control bracket, put theground

Cybex TROTTER Elite Treadmill Owner’s & Service ManualB. Using a Phillips head screwdriver, remove the three screws that hold the bottom backcover

Cybex TROTTER Elite Treadmill Owner’s & Service Manual5. Connect the cables.A. Connect these cables into the display board: the display cable (2 c

Cybex TROTTER Elite Treadmill Owner’s & Service Manual4. Remove the heart rate bracket.A. Using a Phillips headscrewdriver, remove the threescrews

Cybex TROTTER Elite Treadmill Owner’s & Service ManualCSAFE Board6. Remove the CSAFE board.A. Using a Phillips head screwdriver, remove the two sc